Haus Plans ®️
Region: US
Sunday 02 October 2022 03:21:03 GMT
247754
17506
229
21
Music
Download
Comments
Anya Glenn :
There’s nothing worse than breaking down in general
2022-10-02 03:32:26
278
Andrew Allsup :
had our case combine once, chopper bearing went out and it hit so hot I melted and fell into all the other pulleys and hydraulic lines in the machine-
2022-10-09 00:01:12
2
Nathan Prince :
Case 210 20000 for the main wiring harness
2022-10-02 15:17:29
8
astra :
300
2023-02-26 13:15:25
0
Jon Joseph :
A white machine would not do that to you. Which is faster and stronger a caterpillar or a bobcat. Mother Nature says bobcat.
2022-10-02 04:12:19
7
Dalton :
Keep bucket low until the rear part of tracks touch ground then lift will make unloading a lot smoother & look more professional👍🏼
2022-10-03 15:26:11
6
ottos.80 :
On my dads case jx 95 had to redo the clutch it was 20 000$
2022-10-02 06:08:39
18
Jack_kellyy :
20 000 on a motor for a 6400
2022-10-03 01:23:21
7
Christopher :
Damn unloaded the machine with the boom up lmaooo
2022-10-25 18:18:09
3
Ashton Siler946 :
new 3406c engine was 25k. that was a hard check to write
2022-10-26 03:15:20
3
Oláh Velociraptor :
ohio cat
2023-02-12 11:06:30
1
Tahseen_RANGER :
Broken pump and engine becuz forgot to put and add oil
2022-12-14 13:08:15
1
sunst8ofmind :
2k for a pulley tensioner on bobcat. Not my most expensive but most ridiculous
2022-10-25 10:44:27
2
Audie May :
There is no way they came out the same day.
2022-10-06 03:50:12
6
ahmadjay36 :
😊morning am it Jamaica can i jone you to do sum bill houses whit you i love to bill house to
2023-04-20 13:23:38
0
user3255158364313 :
I would HIGHLY recommend loading and unloading your machine with the loader arms down. Tipping point is greatly reduced
2023-02-12 18:47:30
1
charliegorman19 :
Not. bad.
2022-10-23 16:42:17
1
Derek Odom :
17,000$ all 3hydrolic pumps on a tr340
2022-10-04 03:42:25
6
wyohon :
Warranty warranty warranty and when it runs out sell and buy new. It’s saved me a ton of money.
2022-10-22 03:05:56
1
0 :
That will be 10k
2022-10-23 21:19:17
2
User193029 :
5000 replacing a main drive motor on a mini excavator and that was only for the motor without labor
2022-10-23 18:40:46
2
Alex Fucking Dickson :
Trans went out on my 2001 John Deere 310se. That’s was about 7 grand.
2022-10-26 08:58:09
1
Logan Fritx :
rebuilt several engines for 25k
2022-11-26 16:42:00
3
Lance Westdorp :
The most expensive bill on a skid steer that I fixed was 19k
2022-10-02 12:27:38
99
Joe Preston :
That seems like pretty basic maintenance to call the service guy on
2022-10-02 10:07:42
26
Adam :
We got gearbox and clutch work done on a tractor 3 weeks ago about 12 thousand but the tractor burnt down the day after so probably that
2022-10-02 11:54:50
11
reaper :
500 bucks for new tires for my old toro lawnmower. I ended up buying a new one for 3000
2022-10-03 00:03:52
9
Greg Pardue :
Swash plate on a Bobcat 870, $7000
2022-10-02 13:01:58
8
IceMan :
How’s the bearing on the other side?
2022-10-02 03:27:26
7
bob jones :
30000 tannny on a Kamatsu d38 paid 25 for it a year before on bidido no more used equipment for me
2022-10-04 03:12:17
7
ironvaultexcavation :
We had to rebuild the a d10t!! Little over million dollars hehe
2022-10-02 14:55:18
7
Christian :
Whew that block column is 🫡🥴
2022-10-23 22:43:28
7
Trevor Heaton :
Well what was the bill??
2022-10-02 14:36:00
7
Dustin Dickerson :
299D cat skid loader got a hole in the fuel tank in order to replace the fuel tank you have to pull the engine. total bill was $17,000
2022-11-06 22:44:12
7
zkucparts-mandy :
So tiny
2023-04-03 06:14:58
6
DIRT BOSS :
Komatsu D51 Dozer Finial Drive & Pump same job 30k
2022-10-02 16:56:15
4
CAT_DOC :
This is what I do for a living, for a cat deal actually. It can get pretty expensive, especially is you try to take the cheap route the first time.
2022-10-02 17:04:51
4
⃟ :
Skid steer breaksdown? No problem *buys a d10t*
2022-10-02 11:55:59
4
Trenoh Eames :
kubota svl75-2 final drive seal, 9 days down time. lost a bit of money that month.
2022-10-02 04:56:04
4
Stewart :
Repaired my life after my ex- that would be the most expensive
2022-10-02 22:17:04
3
PresidentialBoats :
I sunk a new cat 329 in the mud from a local rental company while clearing 2acres, had to eat a $11,500 bill
2022-10-02 22:44:40
3
user5923035579020 :
2 years ago a guy burned up one of our deere 333 doing forestry work
2022-10-06 01:46:57
3
jamesnelson1369 :
We had a deer 850k the hyd pump Cavitated on. Pump was around 35k and another 5k to flush and clean the system.
2022-10-03 00:38:07
3
Miguel :
Got a used 290 excavator for 60k. Within 5 months we had another 60k in repairs. Good times
2022-10-02 17:32:37
3
Cat_Power_3406 :
Total loss of a skid steer is most expensive repair I’ve dealt with! 😂
2022-10-03 00:48:10
3
Jake Hayes :
Ecm and wiring harness with full service on a cat 279d. 7k:/
2022-10-02 14:00:05
3
G :
2006 asv4810 most expensive repair was over 3k
2022-10-02 12:30:00
3
Josiah Mayfield :
I’ve seen 20 grand worth of parts in a dozer that’s not counting man hours
2022-10-04 02:19:36
2
Jonathan :
36,000 Dollar, your hand on a motor grader, snap the input shaft, chains, and teeth
2022-10-03 02:16:52
2
Jimmy Stuart :
I change those axles and bearings all the time for customers. They can be a pain to get track frame off of if they hadn’t been kept up with
2022-10-03 02:54:44
2
Tyler :
Hello, my name is Tyler Arnold and I work for Carter Machinery as a Product Support Salesman. Message me if I can do anything for you.
2022-10-03 14:05:03
2
Pwilli :
Hagie sprayer we worked on had a leg fall off and dropped onto its face. 97k in parts
2022-10-08 05:59:23
2
Eli C106 :
I didn’t do this but we had a cat 335 zero turn trackhoe had a cab get crushed in by the bucket I think it was 85k
2022-10-18 09:23:39
2
albertouribecoron :
kroil made the job easier
2022-10-17 04:53:11
2
Keith :
I have replaced a few of those bearings. I don't like the design.
2022-10-04 04:53:23
2
Stephen :
Sometimes it’s cheaper to own new equipment, but they break down also just not as much
2022-10-14 01:12:44
2
austinburton262 :
That track and track frame is actually pretty easy to get apart if you have some equipment that can help with the heavy lifting
2022-10-06 02:14:22
2
To see more videos from user @hausplans, please go to the Tikwm
homepage.
