1. Home
  2. Detail

@lisadewiwood: Saingan ama para cewe #suamiistri #pasangan #couplegoal #fypシ゚viral #fyppppppppppppppppppppppp

Lisa Dewi
Lisa Dewi
Open In TikTok:
Region: ID
Sunday 15 January 2023 09:17:37 GMT
30489
340
11
2

Music

Download

No Watermark .mp4 (1.52MB) No Watermark(HD) .mp4 (3.53MB) Watermark .mp4 (0.97MB) Music .mp3

Comments

qq_546
kiki :
iya..dan etiket bicara juga🤭🤭
2023-01-15 10:22:09
1
astondave471
Aston Dave :
🥰🥰🥰🥰❤❤🔥🔥🤩🤩👍👍💯
2023-01-15 11:13:42
1
liliedafsya
NG5F💞Lilie :
benerrrr kaa
2023-01-15 11:17:08
1
vivicute.86
Perempuan Produktif 'ViviCute' :
setuju ka
2023-01-19 12:04:30
1
4n3di
R3Mon :
suami ny tu
2023-03-02 07:52:15
1
fanasky79
jaguar :
wow
2023-01-16 13:28:15
0
To see more videos from user @lisadewiwood, please go to the Tikwm homepage.

Other Videos
انتَ هنا عمري ومحبوبي 🤍
انتَ هنا عمري ومحبوبي 🤍

"Its shizuka:0" . . . #kiminokotogadaidaidaidaidaisukina100#fypage #viral #the100girlfriendswholoveyou #rentarouaijou#fyp #shizukayoshimoto #animeedits


#qoutes #qoutesislami #fypp
#qoutes #qoutesislami #fypp
Here’s how I do full wraps on 40oz tumblers with uneven surfaces in just one pass. Most general knowledge still applies here with just a couple slight changes. Of course I always start off with my @Thunder Laser Nova35 and @rotoboss. Once the handle is off the cup and the tumbler secured, I use my 2” lens to focus to 6mm from the top point of the cup and then again at the bottom. You’ll end up with what looks like a steep angle, but as long as the top and bottom are even, it’ll work out. You’ll need to remove the cone so it doesn’t run into the middle of the cup that will be slightly out of focus. Taping up the air assist is also a good idea. Because it’s slightly out of focus in the middle areas, I adjust my power settings a little higher to make sure it’s get through the coating properly. After those couple steps you should be good to go! I want to give a big shoutout to @gingerspiceco for sharing her tips and tricks on this before I had attempted it. That’s what community is all about! #tumbler #laserengraving #communityovercompetition #maker #makersgonnamake #artist #thunderlaser #custommade #wooddecor #woodworking #woodsigns #handcrafted
Here’s how I do full wraps on 40oz tumblers with uneven surfaces in just one pass. Most general knowledge still applies here with just a couple slight changes. Of course I always start off with my @Thunder Laser Nova35 and @rotoboss. Once the handle is off the cup and the tumbler secured, I use my 2” lens to focus to 6mm from the top point of the cup and then again at the bottom. You’ll end up with what looks like a steep angle, but as long as the top and bottom are even, it’ll work out. You’ll need to remove the cone so it doesn’t run into the middle of the cup that will be slightly out of focus. Taping up the air assist is also a good idea. Because it’s slightly out of focus in the middle areas, I adjust my power settings a little higher to make sure it’s get through the coating properly. After those couple steps you should be good to go! I want to give a big shoutout to @gingerspiceco for sharing her tips and tricks on this before I had attempted it. That’s what community is all about! #tumbler #laserengraving #communityovercompetition #maker #makersgonnamake #artist #thunderlaser #custommade #wooddecor #woodworking #woodsigns #handcrafted

About

Legal