@plumbingsk8r: Can you use a Hole Saw to remove a lead joint? #plumbing #plumbingtrick #tricksofthetrade #howto #willitwork #plumber #drain #remodle #tools #milwaukeetools #project #test

PlumbingSk8r
PlumbingSk8r
Open In TikTok:
Region: US
Wednesday 03 May 2023 18:21:40 GMT
1442026
29074
495
2369

Music

Download

Comments

davidjackson13007
David Jackson7468 :
Good for you you just inhaled a bunch of lead dust😳
2023-05-03 21:27:19
90
blainewardius275
Blaine Wardius275 :
melt the lead. fastest way I've found.
2023-05-03 20:20:16
1
bestdamplumber
bestdamplumber :
@bestdamplumber: I just melt the lead with a torch and pull the pipe out with no problem. Lead melts at 350 Fahrenheit
2023-05-04 02:22:00
3
brian__the_plumber1
Brian__the_Plumber :
Another trick- To put pvc into the dual tite, wrap the end (overlap 1/2") with duct tape and grease. Slides right in
2023-05-03 22:31:59
2
zackaryrogers58
Zackary Rogers :
I just want the lead 😂
2023-05-03 22:30:52
1
anenglishmanincanada
user8822776809752 :
what is the rubber insert called please
2023-05-04 00:00:19
4
jasonmoreno618
Jason Moreno :
I say no. Do the homeowner a better service and update that line as far as you can. If that’s not accessible then I guess this is ok.
2023-05-04 06:19:09
4
aplanty20
AJ Planty :
What is that gasket called that you put the pvc into?
2023-05-03 21:39:19
2
guestx33
guest :
What tool is that and what is it used for?
2023-05-03 20:47:47
1
cebodoido707nyc
cebodoido707nyc :
Drill bit. Is 10 times cheaper and take same amount of time If you know how you do it
2023-05-04 13:00:39
3
kevinleecountry
Kevin Lee :
I bet that’s a real good way to eff up a hole saw
2023-05-03 18:29:00
3
dalmonte20
Tiny Tim :
Legit question, why do you use the right angle drill? Is it kind of like a hammer drill?
2023-05-03 22:16:38
1
cheddarsplumbingco
CheddarsPlumbingCo :
here comes 1M views
2023-05-04 20:15:58
22
dezzznuttz
Robert :
they allow push gaskets above ground where your at?
2023-05-03 20:49:35
4
user2108297607435
user2108297607435 :
bunch of Karen plumbers out there talking shit about this guy's work
2023-05-03 22:13:33
5
cliff875
Cliff :
I use a saw zaw making 2 cuts on the inside 1” wide then a hammer and chisel works nice
2023-05-03 22:07:16
1
plumbace
plumbace :
Melt out save cost of drill bit
2023-05-03 20:24:08
4
justinecker
Justin Ecker :
I usually just fernco it. Unless they want to dig outside. They make terracotta by pvc fernco that go over those ci hubs
2023-05-03 22:26:11
1
abrahamvilla10
Abraham Villa :
Those cut up to 3inch? Or was that 2?
2023-05-03 21:54:07
1
dirtypineapple24
DirtyPineapple :
would of atleast put a fernco
2023-05-06 23:01:43
0
erothfuss
erothfuss :
I just realized you're in Rochester, I thought your picture looked familiar, I've seen your stickers around lol
2023-05-03 21:44:20
1
To see more videos from user @plumbingsk8r, please go to the Tikwm homepage.

Other Videos


About