Hesswoodwork
Region: US
Sunday 03 September 2023 14:25:38 GMT
167108
440
54
3
Music
Download
Comments
Bryano941 :
try to rotate the shafts that the bearing is on. it says it's on a concentric shaft
2023-09-03 14:40:15
25
NymanDesign :
On my jet you use the bolts that hold the barring in place. Use an Allen key and twist it should pivot on that bolt
2023-09-03 14:41:02
14
miradoon :
Bearings should not be touching the blade all the time.
2023-09-03 15:26:14
9
Jay11629 :
Rotate them my friend, they are offset on the “thing”
2023-09-06 01:20:39
8
EEwoodworking :
Yeah the bearings should be eccentric so you turn it and it gets closer or further from the blade.
2023-09-03 20:04:38
4
Kiernan Woodworks :
Do they still make manuals?
2023-09-13 22:21:08
3
Aojgnar :
Rollers are on a cam.
2023-09-03 16:32:12
3
Marc Taylor :
Bearings are in a cam
2023-09-04 00:19:34
2
Bryano941 :
interesting! the manual for that saw shows that the adjustment for them is on the back, but yours looks different
2023-09-03 14:39:19
2
BuckeyeNasty :
"maybe I don't know how to use a band saw" and has like the most expensive band saw
2023-09-13 14:32:46
1
John W P :
Typically the bearings are to support the back of the blade to keep it from pushing backwards. That set up is different than normal tho.
2023-09-04 00:38:56
1
_Its_Just_Jon_ :
They should almost be touching. Not actually touching. Less than 1/16th inch
2023-09-03 17:05:37
1
user2148675309 :
It’s refreshing to see a dude on the internet own the fact he doesn’t know everything. A+ bronco emblem aside i’m following you for being humble.🤜🏻
2023-09-03 16:35:30
1
Jared B :
Loosen the thumb screw, and rotate bearing. I think it’s a cam bearing.
2023-09-03 15:50:22
1
olivia 🏳️⚧️🇵🇸 :
throw it all away or send it to me. it's totally not recoverable.
2023-09-03 14:59:28
1
AbourezkHandmade :
the set screw on the rollers are offset, so when you turn them they'll get closer
2023-09-03 14:42:24
1
Patrick Ferguson :
my jet bandsaw adjusts by an Allen screw on the front of the bearing. and you twist the bearing and it's on an offset lug so it should rotate tight
2023-09-03 14:39:36
1
PythagorUSA 🇺🇸 :
The adjustment is in the center of the bearing on mine. Clean with compressed air, you should see the hex adjustment
2023-09-04 12:38:27
0
troy parry :
The bearings are concentric. As you turn them they will get closer or further from the blade. The rod is not dead center. It is slightly off center.
2023-09-04 05:40:10
0
Love Letters to Doctor Who :
You spin them and they are on a cam to bring them closer. They should be nearly touching but not.
2023-09-03 23:07:44
0
joe :
you want thmlem to be like on the back half if the blade. they should nessacaily be touching the blade but they should b close
2023-09-03 22:51:03
0
Elton Button :
You can try to loosen side screw and then turn the back as the bearing maybe on an offset shaft.
2023-09-03 19:46:57
0
IIIEJIII :
Bro Don’t listen to them. Always haters. Nice Bronco badge tho!
2023-09-03 16:58:24
0
Threefloorsdown :
Eccentric nut
2023-09-03 15:00:27
0
H :
Looks like the screw that’s on the back? There’s the two on the sides and another on the rear
2023-09-03 14:28:11
0
To see more videos from user @hesswoodwork, please go to the Tikwm
homepage.
