Thriving Country
Region: US
Saturday 20 April 2024 10:56:13 GMT
38651
678
92
67
Music
Download
Comments
Just a Guy :
If this is a garden, how are you getting water to the plants?
2024-10-02 12:00:26
0
Patrick :
Thats boots are for!
2024-05-29 15:36:09
4
**++**==**++** :
I see people using these staples, but I feel like I’d end up with a flat tire on my tractor when tilling later. I just use bricks
2024-04-20 13:26:16
0
Itsme.Mario :
my knees and back thank you!👍
2024-09-22 23:02:36
2
Sparky :
it's sand 🤣🤣
2024-06-10 20:12:03
0
Gma Lorrain :
Ingenious
2024-04-21 02:33:18
0
Gasman3 :
Could place a magnet in stick above your groove to hold pin in place as you start it
2024-04-20 12:31:25
1
Thkone :
Make the groove a little thinner so the pin sticks in . Then you don’t bend over to start them . Use the tool
2024-04-20 11:11:15
1
here's Bruce :
but you have to bend over already to just start it, just keep pushing. why stop half way
2024-04-20 16:47:03
0
Little Eagle Flies :
Why bend over to start the pin and then stand up get a stick to finish installation?
2024-04-20 12:23:58
6
user5736948222865 :
Oh my god this is Jason Bourne
2024-05-08 20:46:12
4
Steve 🇺🇸 :
They make a magnetic driver for those fabric staples
2024-05-19 03:20:56
3
BGT35677 :
I did same but I also drill a hole in the middle and put some dime size magnets in drilled hole to hold staples in place
2024-10-04 00:18:00
1
SharkBud :
nice
2024-10-03 01:04:07
1
idontcare123 :
why not just have whoever stuck them all perfectly upright push them in further. getting through the fabric is the worst part.
2024-08-28 01:40:30
1
Jlemons22 :
Sledge hammer…
2024-07-31 02:08:07
1
Erich Schembri725 :
🤔🤪nice
2024-06-11 23:56:04
1
user6218406383688 :
😎😎😎
2024-06-04 23:22:10
1
c_chisel :
👍👍👍
2024-05-29 21:12:41
1
Truth From Flyover Country :
I used an extra long set of needle nose 🤣🤣
2024-05-15 02:10:54
1
cynsbin :
Just asking, you still have to bend over just not push
2024-05-12 14:18:14
1
bradmfj :
What about clay soils on construction site?
2024-11-17 14:08:56
0
Gifrbufjun :
🥰
2024-10-24 13:28:15
0
PaulDamon23 :
And that my friends is how your body stops working correctly 😏
2024-10-11 13:13:20
0
Nurse Nelms to You :
My ground was so hard. Husband and I used our drills with 3 inch nails.
2024-09-30 22:40:15
0
Snatchitysnatch :
Where do I get the vevor stick?😂
2024-09-22 16:59:01
0
Montana Johnson :
less pins and little dirt on sides works great
2024-09-20 05:06:12
0
Chris Mitchell :
How do you get them out?
2024-08-07 15:35:30
0
Geo3240 :
Epoxy a magnet in the bottom of the groove. Staple will stick. Groove may have to be a bit deeper.
2024-07-18 02:57:05
0
Heidi :
Hahaha I just make my kids do it 😂 but this is genius
2024-07-13 16:12:29
0
artc786 :
🤓 ah it's him, Jack Richer
2024-07-08 15:11:03
0
Vloch :
Don’t you have to bend over to start it?
2024-06-21 05:50:25
0
🛡️ Mark 🗡️🕊️ :
But, you have to bend down to get them set in the 1st place
2024-06-11 19:22:05
0
Sparky :
🤣🤣🤣 jesus.....
2024-06-10 20:11:14
0
user6483867590661 :
Nice
2024-06-01 14:04:37
0
ronc2627 :
try it on hard dirt or edge of roadway you'll bend everyone
2024-05-23 18:49:48
0
LibWebber :
Genius
2024-05-23 00:38:11
0
Tony Thrasher :
Put a magnet in the middle and you’ll have to bend over less
2024-05-21 21:11:18
0
yisrealdash :
i just use the heel of my foot
2024-05-20 21:27:25
0
brooks who :
But you already bend over to put them there........🤔🤔🤔 You know they have a magnetic driver made just like that.......
2024-05-20 18:14:44
0
Sam :
Don’t you have to bend over to put the pins in as far as they currently are? See @Steve comment! We use a specific rod with a magnet for this very purpose! Way easy, no bending whatsoever!
2024-05-19 03:31:44
0
Jake Rogers580 :
That’s genius!
2024-05-17 00:13:50
0
Sasquatch :
They make a 3point attachment that puts the fabric down and rolls dirt on the edges so you don’t have to use pins. Just have to get off the tractor to cut the ends.
2024-05-13 17:53:55
0
gizzer1000 :
💯💯💯
2024-05-10 21:36:38
0
DadIsMad :
"You're a god dang genius Gump."
2024-05-10 11:44:17
0
To see more videos from user @thrivingcountry, please go to the Tikwm
homepage.
