Chris
Region: US
Tuesday 19 November 2024 03:35:07 GMT
62887
696
125
25
Music
Download
Comments
ArchieAndrewsAKAChris :
Speed. Slow down. I had similar issues and set my first layer to 20mm/s. Worked fantastic.
2024-11-26 13:01:54
28
Denetor03 :
had this problem right after cleaning, i think you shouldnt use alcohol on textures plates
2025-01-02 12:57:37
2
UtahStickerCo :
To be determined.. I need help lol
2026-04-28 15:02:48
0
Ivan :
Clean build plate, or increase bed temps, at my house is cold so I increased it a bit
2024-12-23 16:39:54
13
Goth Dad :
When I have something like this happen, I usually standby and watch it and most of the time filament lays over it and it’s no big issue at all, probably just a random fingerprint that was missed
2024-11-19 03:40:54
1
Lucas_Mcain :
glue stick
2024-11-19 14:00:26
3
Straightaway :
Hairspray is cheap and easy
2024-11-19 18:22:46
5
Eyalz :
tried everything!!! a 8 euro hairspray fixed the issue. it so stuck to the build plate the cracking is soo satisfying
2024-11-25 19:04:52
3
Cisco :
Get a cold plate.
2024-11-19 14:24:36
2
zagitariuz zodiac :
calibrate the filament. I don't have dryer. so that's it.
2025-01-31 13:15:22
3
vik :
Add glue and slow first layer to 10 mm/s
2024-11-19 15:47:48
1
Артем розповідає :
Add brim with support pls filament and second trick I use washing with liquid soap
2024-11-21 00:07:16
3
Mike :
I slowed down my first layer, helped heaps
2024-11-20 08:14:54
2
northerncreationsprints :
I use plate adhesive. $19 and last forever! Never had an issue since and I print large designs.
2024-11-19 17:56:23
6
Steve O8106 :
Clean plate, level plate, glue.
2024-11-19 19:00:13
21
Simone Hawke :
I clean the plate, then apply some glue to the plate. Usually works for me
2024-11-20 17:01:03
1
NotSure :
tighten the heating plate at the back of thr nozzle
2024-12-28 19:51:06
1
The Nauty Buddha :
use ultra hold hairsp
2024-12-04 17:28:00
1
Mkartz7 :
Just lower the speed of the first layer make the walls 15 and the infill 55 and i promise you it will stick
2024-11-19 08:11:29
5
HowieJ :
A cheap glue stick works
2024-11-19 18:26:44
1
jujee45 :
Tighten the 3 screws behind the nozzle
2024-11-27 03:36:26
1
Garrett Billington :
Recalibrate the bed height if it's been a long time. I've only done it once in the year I've had mine but it made a world of difference when I started having this problem once. Otherwise make sure the bed is clean with dawn soap and warm water and heated to around 60-70C when printing. Bambu makes pla bed adhesive helper as well but it shouldn't need to be used unless you're doing a really difficult print, not like this video is showing where it's super flat and not tall and skinny.
2024-12-03 15:38:15
1
Laksman :
nozzle to low
2024-11-27 18:59:03
1
tuberluber :
Check bed alignment. Possibly use adhesion. Or start print from another place on the bed.
2024-11-19 06:37:35
1
qmansgarage :
increase bed temp if cleaning doesn't help!!
2024-11-19 20:42:25
1
To see more videos from user @3dprintdood, please go to the Tikwm
homepage.
