Derek
Region: US
Friday 27 December 2024 02:11:03 GMT
502225
6589
235
762
Music
Download
Comments
Gary’sFishinMission :
REMEMBER FOLKS ‼️in the real world when the wires are actually attached to something, put the heat shrink on first before you twist wires together and add heat!!!
2025-01-03 03:34:24
189
user6682898878892 :
I have used these, if the wire by chance gets hot it can pull apart. I will not use them again. 🥺
2025-01-11 20:30:12
0
Left :
this method is excellent, however they aren't this cheap and this particular product looks poor compared to the real deal
2025-01-11 10:40:24
0
Red5.0 :
Also the fastest way to lose the connection
2025-01-11 06:03:43
0
Cody Wendt892 :
no electrical tape
2025-01-10 17:06:52
0
Dave Arndt35 :
Where is the flux?
2025-01-08 01:59:58
1
JUST ANOTHER WORTHLESS HUMAN :
they don't work. you burn the plastic away before the Solder melted. takes way to long to use
2025-01-06 18:47:49
2
RedBullChairman :
wire nuts don’t work anymore?
2025-01-10 16:08:24
0
motocross4011 :
Used these. Then quit using these.
2025-01-08 23:47:57
0
nolancannon7 :
Definitely don’t use this for engine harness repairs. That solder has a very low melting point compared to your normal electrical solder. The engine will be too hot
2025-01-09 07:15:07
0
StevanWicker :
I hate these. They fail.
2025-01-03 01:13:44
4
TheRealKJD :
Just use a connector, crimp it, Shrink sleeve
2025-01-04 23:49:09
7
Ken Alvarez689 :
don't use on BOATS!!!!. WIRES COME APART UNDER LOAD.
2025-01-02 15:08:52
3
Bert :
this is NOT how you solder conductors.
2025-01-04 16:35:48
18
Brayden :
If melting point is low enough for heat gun to melt, I’d think the solder would also melt under heat from wires under a load. Neat though
2025-01-02 22:17:47
27
yoopermetal :
Cheaper on Amazon. Using these for years.
2025-01-04 19:34:03
19
Kash :
seals first,then solder
2025-01-01 04:56:23
9
ToxicDoorknob :
The solder didn’t penetrate into the metal
2025-01-08 22:56:03
5
Kyle :
I use these almost daily. pro tip- don't twist. instead fray both ends slightly push together in the tube then heat. more solder gets through the wires. 👌
2025-01-09 04:02:31
5
Alpha_Omega_Man :
I have these. Don’t get them
2025-01-03 12:56:42
27
meer khan :
looks like a inline fuse
2025-01-07 13:11:34
0
That_Doode93 :
for $5 more you can get an extra 5,000 more pieces off of Amazon 🤷♂️
2025-01-06 05:14:15
1
Jack :
Pull on them hard. They will pull straight apart
2025-01-11 23:43:26
0
craneguy :
that's all fine and dandy, but those cold solder joints are trash for can bus systems going between modules and exhaust components.
2025-01-11 22:12:36
0
Gman216 Gman216 :
bought them to try,,, not happy,,, back to old school ways
2025-01-05 16:00:38
2
To see more videos from user @the_asian_viking, please go to the Tikwm
homepage.
