Jeff Thorman
Region: CA
Wednesday 25 June 2025 21:37:15 GMT
262038
8390
38
335
Music
Download
Comments
norris :
omg usa is sooo far behind. never ever install drywall horizontally. it will crack. it needs solid studs behind every joint
2025-06-29 21:24:55
3
Nicholas Merdan :
Installing drywall but using an impact instead of a drywall gun…interesting
2025-06-29 01:06:49
16
Sleepnaught :
Torn paper is the taper's problem.
2025-06-26 01:18:00
94
Shwongalong :
Cut and put cut end in the corner of the room
2025-06-25 21:48:59
41
brandenbrown3017❌️ :
Impact works great especially on old house. sometimes harder Woods and even true would. zip gun still way faster
2025-09-01 13:37:32
1
Just Cool Buildings :
It'll still bubble a lil bit w the Kilz. Not to mention u should be using moisture resistant board in a bathroom.
2025-06-30 13:32:42
9
Skier144 :
For that Kerdi board if you have a gap where your tile ends before the dry wall starts can you just paint the kerdi board or no?
2025-06-27 04:34:40
2
Joshua D :
no moisture drywall next to the schluter?? genuine question
2025-06-26 00:49:12
5
Austin Boles :
always prime paper. might not bubble but you are just taking a small step to help ensure it won't bubble
2025-06-26 02:40:25
6
Van Dammage :
Never had a bubble
2025-06-25 23:03:24
9
c20h30o :
do you put tile on top or you just paint after ? because if you put tile , is there is a problem that is a little torn ?
2025-09-03 06:58:30
1
Michael Angelo :
Should out green drywall there if anything
2025-06-29 02:00:53
2
S G453 :
Tapers make the hangers look good 😁
2025-06-26 05:37:32
2
jake :
I use the same method
2025-07-18 03:09:52
1
Big Daddy :
good advice
2025-06-29 22:13:58
1
CAU :
your the best dude ever!
2025-06-29 01:45:05
1
Alan Janowiak :
The only time I get bubbles on my tape is when I’m taping seams with a primed or painted surface…
2025-07-17 20:53:28
1
glenlisenby :
100 %
2025-08-13 17:09:13
1
JoeSar98 :
I hate that they don’t call it plasterboard
2025-06-29 22:22:02
4
ryan sather :
you gonna slice your fingers using a t-square like that. and use a better knife and cut it harder and it will cut clean like a factory edge.
2025-08-25 00:42:22
1
Will Shera🇨🇦 :
👍👍👍
2025-06-26 02:41:25
1
Matt Wilson :
😳😳😳
2025-06-28 15:38:26
1
Dusty Pollard :
Butting it up to the other factory edge, then butts it up to tile board lol key word butt. So then it would be a butt joint and coated. Zero issue with some ripped drywall.
2025-06-28 00:57:07
1
ArdfartsMcartsNarts :
If your cuts aren't flat enough to make a butt joint, you might be scoring the paper too deep. you only need to cut the paper and the gypsum will break. This video is still correct, cutting that off is a waste of time and a good finisher won't balk at minor scrapes on the paper.
2025-06-26 21:47:42
1
boob :
I don't screw butt joints until 2 butt joints meet each other
2025-07-29 23:42:41
1
To see more videos from user @homerenovisiondiy, please go to the Tikwm
homepage.
