Montana Garage
Region: US
Thursday 28 August 2025 03:00:53 GMT
4246
82
228
1
Music
Download
Comments
Claudie Pritchard :
weld it with high nickel rod, it will polish up just like chrome.
2025-08-29 03:02:56
1
Realistic :
Braze it from the back side.
2025-08-29 00:25:01
1
offgridwelder :
if you can TIG, that's what I'd do. smallest tungsten you have and 1/16 or preferably, 045 filler wire off of your MIG spool. grind 1/8 out from expected weld toe.
2025-09-01 21:02:40
1
Spudwrenches009 :
Unibit the hole from the inside and then wire weld it. Chrome will turn blue
2025-08-29 21:45:04
1
Brunogppi :
Did you try putting a gasket on the valve cover first
2025-08-28 23:03:56
1
Malibu SS 64 :
lower the girdle
2025-09-08 16:12:39
0
calenweed :
come over to my shop and tig weld that on.
2025-08-29 03:54:46
1
cory Beight :
clean off the chrome, tig, gas weld or braze it in .
2025-08-29 16:10:48
1
AnyDayNow :
Tig with silfos/ silver solder. Don't grind it. Use low amps and let the silver flow.
2025-08-29 01:49:43
1
James Miller :
swap the valve covers around so the whole is on the top part of the valve cover
2025-08-29 15:58:02
1
hawaii_steel_customs :
Definitely tig weld it…
2025-08-31 16:57:18
1
davidhannaford3 :
They make one that you can poke through from inside and put a nut on outside no welding. Your going to have a lot of oil in your catchcan though unless you get one that also has a baffle over inlet which they also make. Personally I’d get taller covers with baffles then cut the back corner to clear body and weld a piece back in back there out of site out of mind
2025-08-29 05:22:08
2
ryanarviso197 :
weld it from the inside with a tig.
2025-08-28 16:16:20
15
TheBlownRanger :
Can ya weld it on the bottom
2025-08-28 04:39:48
1
Hunter Ashcraft :
MiG might be a mess, tig would turn out better
2025-08-28 06:52:31
16
David Swanger :
If you weld it from the bottom it may not destroy the chrome as bad
2025-08-28 14:11:13
1
Cave :
hexavalent chromium is bad. not sure you wanna mess with it. maybe you can braze it with brass or bronze?
2025-08-28 23:10:29
0
james :
Weld it from behind probably not chrome on in side
2025-08-29 22:51:47
1
403texas :
jb weld lol
2025-09-05 03:21:54
1
Belikeearl :
can you weld it from inside of valve cover
2025-08-28 14:23:21
3
Wolf :
If you mug weld it, you need to probably use .023 wire and don’t just weld. You’ll need to tack it all the way around. More than likely you will burn through that valve cover. Def grind the chrome. When you are done, smooth out the weld and you can always seal it with silicone around the weld if you have to. I’d rather you get an aluminum fabricated valve cover and weld an aluminum bung to that. If you can find one that fits
2025-08-29 14:04:17
1
geraldwiesmore :
Send it to me and I'll TIG weld it for you.
2025-08-29 01:40:03
1
Rob's Metalcraft :
tig would be best way but you need to remove chrome or it will contaminate tungsten. mig will work as well but won't be as nice looking .
2025-08-28 20:45:53
1
For The Insane :
Use a AN bulkhead fitting that will seal on the inside with a O-ring
2025-08-29 01:10:25
1
1star21 :
Grind inside. Tack around inside while holding frozen shop rags around outside.
2025-08-29 14:11:15
2
To see more videos from user @montana_garage, please go to the Tikwm
homepage.
