Lets Be Techs
Region: US
Thursday 08 January 2026 13:58:45 GMT
25493
1615
40
75
Music
Download
Comments
austin.y24 :
Those beacon units suck at what point do you just rip it out and put all mechanical components in or a ke2
2026-01-08 14:58:40
11
christhierman :
Good diagnosis watch out for the cables to though I personally have had 4 or 5 bad cables and the the drive motor was good.
2026-01-08 15:10:50
5
Jeffrey D ❌ :
if you put that board into test mode it will cycle that stator opening closed three times you don't have to power cycle it
2026-03-07 22:58:40
2
TheScootinCanadian :
What do you like more? EEV's or TXV's?
2026-01-08 14:41:46
3
Drinks-In-Forests :
how did that valve stem core end up in there??? 🤔🤔
2026-01-08 15:39:57
4
Dalton Ford :
I’ve always replaced the wire harness and motor both seems to be a very common issue with these
2026-01-17 04:30:21
3
Sergio Martinez :
I work as in house technician for a restaurant chain I do everything means all of what’s in a restaurant got hvac certified last year and like your videos their on point easy explain and so helpful I just want to say thank you for sharing.
2026-01-08 17:30:46
5
Jwillssickwhiteboy69 :
Had a beacon system on a vault cooler at 7/11 3 Evaps 1 master and 2 slaves on a multi unit condenser. What a nightmare to trouble shoot
2026-01-08 19:22:52
6
Dallas Sovine :
We have a mix of beacon 2 and intelligen. Those exvs and defrost sensors were our most common failures.
2026-01-09 12:19:32
3
Bhav45 :
This video is what I needed to know. Compressor kept icing up even with clean clear sight glass , I typically don’t work on units with EEV but this helps a whole lot . Thanks for the video
2026-03-11 02:02:08
1
John Nanthavong :
thank you for being one of the few people I know that have trigger control
2026-01-24 22:04:05
1
reefer_tek :
Those white boards gave us some problems 🥴
2026-01-09 16:37:44
3
David Miller :
My OPINION, EEV’s should not be used as a pump down device even if they’re pump down rated. I think they should always have a PDS in front of them.
2026-01-08 19:26:01
2
JT :
Great video Thanks for the information
2026-03-07 02:32:13
1
JT :
Great video
2026-01-08 15:30:33
4
after :
👌👌👌👌
2026-02-20 16:12:14
1
DarinCHudson :
Where is the nut from the old one?
2026-01-08 17:36:40
2
navycampr :
Use the EEV magnet tool sometime, want to see one in action!
2026-01-09 11:18:39
2
tBIGzb :
hammering home
2026-01-10 07:38:46
2
Jmoney70 :
Them boards are junk I take them out use a ke2 .
2026-01-10 03:25:50
2
Fenchi :
These valves are like 500 $ so rip off
2026-01-09 01:33:14
3
Window98dust :
Had the same thing happen to me but on a freezer. POS units
2026-01-10 01:12:17
2
SDSteve :
Maybe a little dielectric grease on that plug? 🤷🏻♂️
2026-01-09 05:54:09
2
user2711581934385 :
Best Informational Video i've seen, i work on beacon 2
2026-01-08 17:10:12
2
To see more videos from user @letsbetechs, please go to the Tikwm
homepage.
