Raymond Gen❌️
Region: US
Sunday 11 January 2026 12:17:02 GMT
122227
764
52
49
Music
Download
Comments
MadWolf :
Half of 45° is 22.5°. I could tell you were off when you set tour trim. I saw that you moved the right one away from the 2X4 to bring the gap together
2026-01-13 14:17:20
95
RyNo :
Try making the cut again at 22.5 deg lol
2026-01-13 03:31:16
32
BiggDaddy86 :
I’m glad I’m not the only one that seen that 😂
2026-01-13 03:50:18
39
🏆WK's Creations🏆 :
Let me see the inside. I think it’s off a little lol
2026-01-11 12:54:09
47
earl8913 :
Am I the only one who knows that half of 40 is 20 and not 22.5. everyone saying half of 45 is 22.5... the tool was at 40 not 45.
2026-01-28 02:39:55
3
mayham :
Whatever happened to the speed square six bucks at any hardware store
2026-01-13 11:41:01
0
Fenrir :
its 22 1/2°
2026-03-22 23:48:59
1
gz_tiktalker :
I’ll just measure twice
2026-01-28 18:58:42
1
SmkyMtnRealtor :
The math don’t math. But the guide does legitimately say 25 degrees lol
2026-05-09 12:38:26
0
user1374571165584 :
22 1/2
2026-01-13 04:06:30
0
RightOne :
Id say it was more like a 27 degree. Also you didnt need to swivel the mitre saw, you were cutting square edge 1x6, cut on the sane side and flip the piece.
2026-05-13 06:42:35
0
Raymond Gen❌️ :
The 25 degrees is correct. Everyone notices when I had to adjust for the gap but that is because the 2 x 4 moved and at the end of the video you can see the crack where the 2x4s come together and it wasnt there in the beginning.
2026-01-13 19:47:33
3
cmartin2230💚 :
if you build the wall then you should know the angle. or be a good craftsman and write your angle on the board
2026-01-19 04:08:00
1
Ryker :
I've used this tool for years ..they do work ,he just had his angle finder off a bit before he went to the saw ...dont let the demonstration decide for ya
2026-01-13 10:11:18
3
codiconrad499 :
lay the blocks where the intersect over top eachither then go take one piece to soeed square and figure out angle like a normal person
2026-01-21 23:56:15
0
406living :
Pick it up and trace both sides
2026-07-02 04:53:27
0
shane :
yeah 22.5
2026-03-17 18:03:33
1
Stew :
Nail em and caulk it.
2026-01-13 16:27:06
0
boomer_bends :
I wouldn’t buy that if someone else paid for it. *Moves right side to close gap and says “See! Works perfectly” 🙄🤣 I wouldn’t show my face either 🤣
2026-01-14 04:37:47
0
banno54 :
I’m so confused. He made this a lot harder than it has to be. If it was a 40 degree angle. How does 25 & 25 = 40. It doesn’t match.
2026-05-19 03:18:12
0
sailingmil79 :
My lazy ahh would’ve just marked lines on the ground then bondo my mistake.
2026-02-11 04:22:31
0
Vegas - lights :
You made the cuts just mark the saw
2026-01-15 18:08:20
0
Vegas - lights :
Neo angle
2026-01-15 18:09:02
0
jon :
How old is that saw? I use dewalts daily prolly one every two years commercial use thirteen years I don’t see them with the plastic number cover ever!my old ryobi table saw has that but it’s at least 20 years old!
2026-01-23 04:57:17
0
To see more videos from user @raymondstoolshop, please go to the Tikwm
homepage.
