sandymakes.ca
Region: CA
Wednesday 21 January 2026 23:14:11 GMT
27602
273
118
3
Music
Download
Comments
ryangoslinklover420 :
Filament 100% you have bad filamet
2026-01-24 08:03:45
2
Anto C :
Have you cleaned your bed? You should clean it regularly. Use dish soap then isopropyl to remove residue and don't touch it with your fingers. Oils prevent good adhesion
2026-01-22 00:05:16
3
thatbitchsatanica :
Wash the plate with dawn dish soap and a new microfibre cloth - I like to use dawn platinum and alcohol
2026-01-22 00:25:31
9
❌ThunderPC❌ :
Check screws on the front AND back of heat block if you haven't recently. Common A1 issue.
2026-02-03 16:24:14
3
90xj :
clean the plate, make sure it's level then spray with hairspray right before it prints. cheap spray works good and holds the filament in place
2026-01-22 17:00:21
2
Raul Derbez :
Do you recommend buying one? Another creator recommended the ender 3 pro
2026-01-21 23:18:42
1
King Jeff 🇨🇦 :
I would try raising the nozzle temp 10 degrees and maybe turn off the fan. the first one you pulled out of the garbage the print came loose from the table. also change the setting so the nozzle doesn't pass over the print but goes around the print, makes for longer print time though.
2026-01-22 11:48:23
1
⚡️MORTADELLICA⚡️ :
Clean then brim.
2026-01-22 10:14:45
1
Me and Vito :
Get rid of that plate and get one of those blue plates
2026-01-22 01:56:24
2
massivelaserbeams :
I use Aqua net ultra super hold on the build plate. it’s just insurance.
2026-01-22 15:11:46
1
Helene - Lovely Designs 🇨🇦 :
Wash your plate.
2026-01-22 00:17:52
1
Raul Cornejo943 :
did your room temperature change if it did that's why
2026-01-22 20:27:42
2
christoph :
power shortage
2026-01-22 09:16:36
2
kiwi_shenanigans :
Uh i think a clog and the other one moved
2026-03-17 01:25:57
1
niwde3d :
dry it
2026-01-22 10:13:35
1
The bmx king :
you need to put glue on it
2026-02-17 02:19:40
1
⬇️⬇️⬆️➡️ :
What are these comments, he said at the end? Not the beginning
2026-01-22 11:38:38
1
Raul Cornejo943 :
try covering your printer so it keeps it's temperature
2026-01-25 12:45:40
2
king tutt :
level the plate and add some corner brims
2026-01-26 01:55:02
1
MosesManorTX :
Don’t be too quick to blame the printer looks like a bed adhesion issue. Clean the plate literally wash and fully dry. Also make sure your z isn’t too low. And make sure your heat settings are correct for your filament. I always use a layer of hyperlock - a bed adhesive- it’s not necessary at all but it’s a nice insurance policy especially for smaller parts.
2026-01-22 14:52:03
1
notesfromstew :
so what was the fix? I am also having this issue.
2026-01-26 22:30:11
2
NotGoobs :
That can happen when the print slips from the bed. Check the bed temp and nozzle temp
2026-01-21 23:34:25
4
Free AI Money :
garage is cold, this the issue.
2026-02-09 21:44:24
2
ben🤫🤫🤫🤫🤫 :
put bed at 80 degrees and nozzle 170 or 180 put glue in board and let it steam on the board then do that every time
2026-02-20 22:50:02
1
dannyyyyy✝️ :
try washing the build plate with dish soap and warm water
2026-02-17 00:13:19
1
To see more videos from user @sandymakes.ca, please go to the Tikwm
homepage.
