CapitalCityCreations
Region: US
Friday 24 April 2026 15:18:46 GMT
11549
49
38
21
Music
Download
Comments
BioMed Ben :
It looks and sounds like the extruded tip is dragging along the build plate. Make sure you’ve got the proper z-offset.
2026-04-24 16:24:36
0
aviatorr :
how do i fix ittt
2026-07-23 13:07:11
0
El Padrino Art ✍🏽 :
Clogged hot end . Happens if u use PTG on your printer
2026-04-24 16:35:40
3
blue7 :
https://wiki.bambulab.com/en/a1/maintenance/manual-bed-tramming
2026-05-01 03:33:54
1
Fer LCV :
Bad calibration and prolly humid filament
2026-04-24 18:32:36
7
frog :
Your zoffset is too low. Relevel your bed.
2026-04-30 16:34:55
3
alguien-🪖 :
You need to reforce the claws inside the hotend
2026-05-01 19:31:22
1
lf3rn0 :
initial layer hight to small, needs to be at 0.12 or 0.2
2026-08-19 11:51:56
1
tomsmith58 :
I had loise,screws behind the heat plate snd the plate itself
2026-05-21 23:21:33
1
Mr.2seater🚶➡️ :
might want to clean the plate and add glue, do not use rubbing alcohol on the build plate and adjust your z offset
2026-04-24 16:19:58
1
MarMar :
Re-tighten all the bolts holding the nozzle assembly
2026-04-25 22:21:40
2
Luna Layer Studio :
New nozzle … happened to me a couple of days ago and bought a new nozzle and now prints perfectly.
2026-04-26 01:09:52
1
muddy9069 :
Z-offset is way to low.. back it off at least .30.
2026-04-25 14:49:06
1
Henndawg :
Partial clog.
2026-04-28 04:24:11
1
XXMAMACRAFTSXX | MAXIEN :
I had this issue when I overlooked one small thing - it drove me nuts !! Make sure you put the clamp on the nozzle back on correctly.
2026-04-24 16:45:11
1
Ed :
Clog
2026-04-24 21:10:50
1
PomNerds :
Make sure the filament you have loaded is what the machine thinks it’s printing. If that correct you likely have a blockage.
2026-04-24 16:15:40
1
Raul Cornejo943 :
clean your plate
2026-04-27 11:04:26
1
Fsk_Mike :
Glad to see it’s not just Flashforge users
2026-04-24 23:39:14
1
marioz125 :
take the plate off the front of the hotend, take the sock off, take the extruder off, and tighten the screws holding the stone to the extruder kit. then put everything back on. i had the same exact issue on my a1 mini a few weeks ago.
2026-04-24 15:38:58
2
obscure fate :
had the same issue on both a1 & mini. take out your nozzle. tighten screws behind it. fixed the issue for me. there could be other causes. but that's what fixed it for me. also fixed the filament not extruding issue I was getting. its now a standard part of my maintenance to check them. no issues since.
2026-04-26 19:20:10
1
Fer LCV :
Calibration wayyyyy to close to the bed
2026-10-11 07:28:43
0
Shann❤️ :
same thing happened to me and I still haven’t fixed my printer. The company sent me a new build plate and nozzle.
2026-05-09 05:49:27
0
𝓑𝓻𝓸𝓭𝓲𝓮☃️ :
Your nossle or its clogged use the needle it came with and heat th nossle up tp 270 and stick the needle up it
2026-04-25 20:16:52
1
SlickSpiz :
Are u using Esun? 🤮
2026-04-25 00:35:44
0
To see more videos from user @capitalcitycreations, please go to the Tikwm
homepage.
