Mawele Lethabo
Region: ZA
Friday 08 May 2026 18:24:34 GMT
63466
2491
76
271
Music
Download
Comments
Lesedi Lelosa :
This flange made me pass my trade test on second attempt😭😭😭😭
2026-05-09 04:15:33
32
khumielehumo :
Distance between the holes is 37.5
2026-06-07 06:42:15
1
Waterberg :
i remember stopping after the first hole during my tradetest to secretly ask for a new blank block , ended up doing the second one in 20min and was a brilliant pass (by my standards at the time) 🔥🙆🏻♂️😭
2026-05-09 15:55:20
6
Linda Mkhonto :
Flange is phased out for apprenticeship
2026-05-09 02:49:59
1
Zikhwe :
No need for calculations... check out my pinned video
2026-05-21 09:45:41
2
Masie Levy :
Thank me later
2026-05-09 06:08:51
8
PÚSÊŁÊTSÖŴ 🦋 :
Can you please explain the calculation
2026-05-09 05:33:56
4
thxiska_ak :
and if i may ask what are the requirements for the course at UV? 😔
2026-05-29 22:59:06
1
philagazman :
It is not supposed to go all the way down ku jig 🤞
2026-05-09 10:19:16
2
siyadaba23 :
Ola bafo next month am doing my trade test on Machenical fitting any advices plz
2026-05-09 08:59:30
1
Mor Sea :
Nice, can you share those documents please
2026-05-09 04:57:55
2
Noyolo :
Where did you get those numbers or how please A up to D how to get the numbers
2026-05-08 20:31:19
1
Jasmine 404 :
Mawela my guy which institution are studying with and how much is the course pls 🙏
2026-05-10 05:49:32
1
luckzo7 :
I set up the whole trade test Centre there, from an empty work shop to what the Mechanical workshop looks like. At once was the only black trainer at Mechanical. Did the design for the pipe system and asked draughting office to draw. Did pipe fitter training and trade test from learning material to trade test. I did a lot there. The current trainers were once my students. I am the 🐐 of that place.
2026-05-14 19:28:39
1
ThulaniMaseko :
Just get your references correct then everything will be easy
2026-05-09 07:17:19
1
Fumene :
ay uyinkunzi mfowami
2026-05-09 03:56:07
1
Smomondiya 💋 :
Can you take through the calculations step by step I’m a bit confused
2026-05-09 05:43:57
1
Given and 37 others :
wenze 20 per day kujike kungene eyodwa
2026-05-09 07:45:56
3
@mgazura :
danki bhuti 😂😂 ama 5 whole uyangikhipha
2026-05-09 07:15:51
1
bernad van vyk :
easy task
2026-05-09 06:36:45
1
CràzyTèE😋😎 :
Eish I remember doing this back in highschool
2026-07-21 18:03:47
1
Sthe :
😭Neh onnn
2026-06-22 13:50:03
1
pretty@91 :
hallow bafoh I need more explanation on doing holes
2026-07-21 10:29:38
1
Adv Chakalaka :
I see the calculations but how to set these decimal values on the vernier
2026-08-13 06:23:53
1
To see more videos from user @kwote_45, please go to the Tikwm
homepage.
