Misha Panchishak
Region: US
Thursday 14 May 2026 12:26:23 GMT
185924
3259
181
30
Music
Download
Comments
oakandarrowstudios :
The tool you want is a rotozip not a router
2026-05-15 04:12:00
140
Peter Smith84462 :
its not the right bit need a spiral flush bit with a bearing that runs along a flat edge to stop it wondering
2026-05-15 12:45:22
138
Matt Bouressa :
You need a flush cut bit. It has a bearing on it
2026-05-17 02:49:08
157
curt :
Duuuuu…wrong bit dude. The one you need has a bearing guide on the end
2026-05-14 18:37:45
112
Jayyydn :
Yeah that’s definitely not the right bit
2026-05-16 20:56:09
13
jimboslice028 :
You need the one with a bearing at the end. Glides nice and smooth, the tool does all the pulling
2026-05-14 14:10:20
82
mariocervantes813 :
Much better to use for this purpose. Dust shoots down and away. 1/4” cut so less dust. A lot smoother and longer lasting. “Whiteside Router Bits RFTD2100 1/4-Inch Cutting Diameter and Spiral Flush Trim Bit with Down Cut”
2026-05-16 01:22:37
18
Michael Anthony :
Everyone is wrong. You need an uphill downhill spiral bit.
2026-06-19 12:59:38
2
B3llyg0a1 :
From the looks of it. Depth wasn’t right
2026-05-15 21:57:10
7
Bill Bingham705 :
safety glasses 🕶️
2026-05-22 00:10:19
2
Kirk Blanchard983 :
Definitely not right
2026-05-16 00:30:33
3
Petr :
wrong bit bro
2026-05-14 17:43:52
38
Bonter83 :
its the right bit. you didnt do anything wrong the second time. your problem is, is that the bit isn't out of the router enough. you're carbide isn't deep enough
2026-05-15 19:51:04
5
mscoldschooler :
wrong tool bud
2026-05-15 10:22:30
16
Theo :
Dont they do it on dry wall
2026-05-16 04:41:18
6
Higa-Brown :
I’ve used this type of router bit for the exact same application your bit is just set too far into your router and always go clockwise while cutting
2026-05-15 06:35:15
7
Little Bridge Workshop :
Guide bottom bearing flush cut bit. You’re using the wrong one
2026-05-14 16:17:45
9
Jord :
Wrong bit. You need an Up Spiral router bit. Pulls chips, sawdust etc up and out of the cut.
2026-05-15 16:57:03
7
Justin Donovan :
wrong bit. supposed to have a bearing.
2026-05-16 00:15:07
3
PaThOGeN74 :
That was painful to watch
2026-05-24 23:43:30
3
Gennadiy :
Wrong bit and terrible tool brand! 😂😂😂
2026-05-16 05:36:23
3
user888479219112 :
protection
2026-05-16 16:13:44
2
Kade Castles🇨🇦 :
I think the depth is too much for the bit..
2026-05-16 07:08:56
3
user99203907250 :
I like your bags😂
2026-05-15 02:11:40
3
Levib270 :
You don’t have the wrong bit at my construction company we always use that one. One thing you could do Is set it a little deeper. You want the entire thickness of the sheet in the center of the bit where there’s the most bite
2026-07-02 23:54:44
1
To see more videos from user @winnidesigns, please go to the Tikwm
homepage.
