Mark DeCola
Region: US
Monday 29 June 2026 01:50:31 GMT
156806
16360
132
65
Music
Download
Comments
Noctis :
Rubber Isolators (ISO Mounts): Check these inside the drum for cracking, separation, or torsion.Worn Bearings: Worn or damaged vibratory bearings in the drum can cause loud noise and reduce efficiency.Eccentric Weight Shaft: Check the drive shaft and splined coupling inside the drum. If broken, the motor may spin without turning the weights.Drum Scrapers: Ensure scrapers are not rubbing too tightly or harboring debris that could impede rotation.
2026-06-29 02:03:14
280
Tobatsi :
You forgot the flashlight 😭
2026-08-01 21:01:57
125
BeetleBailey :
it's the thingamabob that's under the duehickey!🥰🤣
2026-06-29 02:08:59
244
Chrisso :
Hey mate if you flick us some more info on the machine I should be able to provide you some schematics and diagrams to help out
2026-06-29 02:21:10
47
Jake E. Burnett :
almost wonder if when u took the lines off it created an air pocket
2026-08-02 12:13:30
30
Brian marek :
I say the fronts good enough fix it when the front goes
2026-06-29 21:23:39
5
Mangum :
Good luck! Love watching the videos, I’m sure someone will chime in with some good ideas. But your common sense approach seems to work pretty good!
2026-06-29 01:57:38
29
Daniel Gerald Atkins :
There is a hub coupler that goes bad a lot chews up the rubber we get rid of our cb24 roller when the dum bearings and seals go bad . Leave hydraulic hoses on take the two Allen bolts out see if coupler is chewed up
2026-06-29 09:25:27
26
Dakota Parks :
pull the vibrator motor while its off check for rotation if it doesnt rotate you have a fluid problem. if it does rotate check to make sure you have the coupling/shaft keys installed properly or are not sheared off. Those are some of the easier checks to do.
2026-08-02 03:07:12
8
Kreston Stevens :
Wish I could help, but I’m here for the journey!
2026-06-29 02:00:47
19
RJ :
I'm in Scotland 🏴 so when I see your vids I know it's time for bed 😭😂
2026-06-29 01:59:10
70
Harvold :
As a former employee of Domino’s, we ran across this a lot in our delivery vehicles. It’s low on fluid and then needs adjustment in the flowbehead extender valve.
2026-06-29 11:55:11
14
Tommy :
If I had to guess, there’s got to be a bearing that’s bad.
2026-06-29 20:22:20
5
Mechanic :
open the drum the pads are gone or ya broke shaft
2026-06-29 02:45:03
5
Dickens Cider :
It sounds like the motor is shot. The pump is definitely sending fluid down there, so it's probably going straight through the motor, and the pulldown you hear and see is the restriction of the motor, but it's not turning.
2026-06-29 12:13:34
5
Xaq :
Have you checked the hydrocoptic marzel vane? If that's ok then it's likely the ambifacient lunar wane shaft.
2026-06-29 10:07:13
9
Zane :
i have no idea. hope this helps
2026-06-29 02:07:02
5
Medic_536 :
So early there’s no suggestions for help in the comments yet
2026-06-29 02:01:06
22
Oliver Doucette :
there's a l8ght in the drum
2026-08-02 20:18:32
7
DoubleT’s Small Engine Repair :
I hate working on newer equipment. It’s so complicated.
2026-06-29 02:08:48
5
Alex drozy :
Most rollers have a plastic belt inside that drives the weights, either way very likely the issue is internal with what your showing but I would swap the motors first because that is way easier that tearing the drum apart, I work on hamm rollers everyday not so much cats, but there is a lot that goes into rebuilding the inside of a drum, definitely get the procedure Manual, the weights inside are timed
2026-06-29 02:40:53
5
️ :
im first
2026-06-29 01:54:04
7
brucealmighty :
thats your flashlight inside the drum💀
2026-08-03 15:11:09
4
shitbox_n_such :
Could be a bad solenoid, could also be the harness going to said solenoid
2026-06-29 17:38:39
4
Just.Jeremy :
did it work before you tore it apart
2026-08-02 21:23:48
4
To see more videos from user @mark_decola, please go to the Tikwm
homepage.
