@niwejacob: Simple and easy way of treating walls affected with penetrating Dumpness. #construction #kampala_tiktokers #fyp #viral #painting

Acram :

bro dont joke with water ebyo byonna bya kugumya bagagga but it actually comes bak

lamar :

Item 1 : Expose the wall to brick work remember the plaster is already affected and you have not yet delt with the problem. Item 2 : Apply strong coats of SBR using Cem 2 as an activator onto the brick work using brush , Item 3 Re-plaster using SBR latex into the plaster to help protect and cure . 🫡

PETRAM VENTURES LTD. :

NB: Bricks,concrete naturally contain hygroscopic soluble salts that can pull moisture right back to the new paint in a few months and efflorescence is a symptom of moisture movement and soluble salts Scrape off the lose paint,remove contaminated plaster since its compromised right back to the original block work. Treat the salts on block work by applying specialised anti-salt impregnating primer (imported-deep penetrating silcate primers) of specialty damp-proof and salt encapsulating or plascon alkali resistant primers/wall sealant so that it soaks deep into pores. This stops residual nitrates and chlorides from migrating forward to the new surface.Avoid using contamintaed water and sand for replaster. Superflex is not a breathable mineral piant...if you can use traditional alternative of site-mix lime wash using hydrated building lime,clean water and sometimes tinted with alkali-resistant mineral pigments that mimic the breathability and chemical bonding of commercial lime paints. NB: Using an elastomeric paint like superflex to fix active efflorescence is a high risk gamble because it creates a thick,rubbery continous plastic film designed to block water and trap water vapour behind the coating..........but it works only if you completely eliminate external water intrusion

Yusuf Ug :

I always do under pinning and the problem never comes back

mc SMITH :

hello Mr am looking for work am professional in doing waterproof

Alex Kafumisi :

waterproof with injection cream and plaster again usuing sika latex admixture. thank me later

Build your Home 🏠 with us 😊. :

1) get the defected plaster/render off till blockwork/brickwork is exposed 2) apply the first coat of Sika-seal slurry well steel floated 3) upon setting, apply new plaster/render ratio of 1:3 4) apply a 2nd coat of sika seal slurry and leave it to set. thank me later.

exotic: :

can you please come back after 2 weeks and show us that same wall, personally am not yet convinced

jk logistics :

nooo it will get off am sure take your time and identify well the problem

user7500408237090 :

So do you do that after solving the water dumbness issue or before

Hector Ronnie constructions :

I wonder, imagine treating outside not inside dats not true it's for time being

Sam Jonans :

but now you are applying the treatment on the affected wall already .. you would have removed the plaster first and re start from the bricks and if possible you could have installed another DPM on the bricks since it's raising dampness

Samsung fadah1🇺🇬 :

If u can get this then u have permanent solution

K.T TRUSTED PAINTERS🎨🎨🖌️🖌️ :

a few moments later

uncle God :

gambling

ndaulabrian :

Have u addressed the cause ?.

wizz :

mpa kumulimu papa

Kampala Painters' HUB :

boss u shld have scrapped off t brick level.treat from tht level

إبراهيم 7 :

ebyo bijakuvaako unless nga ojeko plaster bro

Franklinevazquez :

nze obuzibu mbulina munda woka ebweru wali fine mumpe ku magezi ba Engeneer

LUKMAN YOO :

jefflmx :

I need your service too

idol :

I need your service urgently

sowedi gulume :

yeah

OD Interior Professionals :

mr.niwe, I have this same thing in a flat on the 2nd floor. it'd not near a bathroom, but it has effervescence