StonedInTheYard
Region: US
Tuesday 18 August 2026 09:55:28 GMT
42982
3426
121
61
Music
Download
Comments
buckmainly :
OEM Part # 037-6024-00 • Fits: MZ 2010-2022, MZ Magnum 2013-2025, MZ Rambler, Revolt, Stand-On, ZT Avenger • Industry standard: 6305-2RS-C3 - 62mm OD x 25mm ID x 17mm wide, sealed, C3 high-speed/high-temp version • Replaces Bad Boy OEM# 037-6024-00 How many you need: • 2 bearings per spindle • So 6 bearings total for a 3-spindle deck - 42", 48", or 54"
2026-08-18 12:07:16
60
justinkeller205 :
The fuck is a proboscis??? [Laugh approved][Laugh approved][Laugh approved]
2026-10-14 23:36:24
1
71triumph :
I can’t say the bearings brand name 😂 but it’s Foxtrot Alpha Golf
2026-08-18 11:04:03
29
Winchester kid. :
You are the most "realistic" mechanic I've seen! This is how real guys work on shit!...Thank You!!...Cussing, bitching and complaining how manufactures build shit..I'm following you.
2026-08-18 11:49:45
53
Cam Reagin :
Haven’t heard a gravely yet, have you 🤣 that SOB is the loudest mower I’ve ran.
2026-08-18 23:48:13
8
Matt Butcher :
no wonder they put the word bad in it because its a pos .... so did you get that off without bending the pulley ? put the bolt back in a use a air hammer on it .. have fun dropping the deck to do the sides
2026-10-11 03:08:43
3
DillioMcStuffins :
Shhhh my shows on
2026-08-18 17:21:25
13
Dakota Burr :
Man I thought I was going crazy. I thought the same thing and even asked other people and they said they didn’t hear it
2026-08-18 22:54:10
8
Cody Wilkins :
What residential zero turn do you recommend? Been looking at these magnums with kawi power
2026-08-18 19:26:50
9
Jd’s small engine repairs :
Not a great test for the impact. Those spindle pully bolts aren’t very tight. My 1/4 in electric ratchet gets them out. But the blade bolts and getting the pulley off the shaft are another story lol. But I wanna know more about the impact! Tired of my crap on one.
2026-08-21 01:21:06
6
justanotherpulltab :
what zero turn do you recommend? looking to buy new...probably 54in cut
2026-08-19 00:24:48
5
boogz :
prolly be easier if you loosen up the allen screw
2026-08-18 19:07:46
5
Ed :
I have a bad boy my pulleys have a set screw
2026-08-22 03:13:55
3
c.tabb15 :
Skf bearings
2026-08-19 17:19:33
6
travisconnell248 :
As a parts guy for John Deere who don’t sell shit else. Parts tree for my anythang else needs. 🤦😂
2026-08-20 02:51:38
4
user28483848292 :
My Deere rider sounded like that. Get some grease in those spindles. Typing this down the road from the timken HQ in canton Ohio lol
2026-08-19 16:06:08
5
Eric Cartman :
Right angle impact has saved me a few times, I use kobalt 180 ft-lbs
2026-08-18 12:45:32
6
roachscurrencyandcoins :
Use a mirror
2026-08-18 10:40:00
5
Jug304 :
he said this one, no that one... one of these spindles.. took me out
2026-08-18 10:02:07
7
Steel Dirk :
Is there a part 2
2026-08-19 14:23:51
3
Harvey Hasty jr :
When I replace bearings I pop seals off both side and pack with red and tacky they last long time 😁🥰
2026-08-18 19:03:49
3
Christopher Patchin :
Hahahaha I work at a bad boy dealer. Put a 19 end wrench on the top spin it till it hits the deck hanger then use the blade to break the bolt on the pulley. Yes the tank is bull shit🤣
2026-08-18 22:53:16
4
Luke Lindemann :
Used these on my 36” stand on. The 2RS is supposed to handle heat better. Bad boy needs to change their name to bad engineering
2026-08-22 10:45:25
4
Fentastic Four :
Koyo are also very good bearings.
2026-10-13 06:12:17
1
jor-_________=\ :
Hey boss just to let yk you need creepola by mule head brand it’s the best break it loose shi on the planet ik a lot of people say that about a lot of bs but just trust me
2026-10-06 01:00:23
1
To see more videos from user @thestone101, please go to the Tikwm
homepage.
