sheetmetalsamurai
Region: US
Tuesday 01 September 2026 19:00:00 GMT
339550
7020
160
224
Music
Download
Comments
komwa1 :
Nobody that uses a grinder much keeps that guard on
2026-09-01 19:26:19
206
Milo :
yeah i removed my guard as well, needed some more space...
2026-09-02 07:57:09
379
Jet :
Take the guard off so you can fit a 9 inch disc on it 🙏🏼🙏🏼🙏🏼
2026-09-01 21:39:04
44
Hanlon’s Backyard BBQ :
I bet ya safety wouldn’t even notice on job sites 🤣
2026-09-28 00:58:43
2
Liam_dawsonn :
Keep this nut on and you can use the fibre disc
2026-09-02 06:19:25
26
Molten metal messiah :
It is very important to keep your guard on your grinder.Never take it off as soon as you purchase it.Never do that, never have a pile of them in your toolbox.From all the grinders you've had in your welding career😁
2026-09-01 19:07:53
48
John Murray :
I typically throw the guard directly in the garbage after I open the box in the shop, however, on the job site this might just work 😏
2026-09-01 22:36:04
8
Brayden Mckelvy :
Any advice on welding with 7018
2026-09-02 00:44:46
3
LDG :
The guard is supposed to protect your hand? I was taught it controls where the sparks go
2026-09-02 12:52:12
2
Dg :
He grinded the grinder so the grinder grindes better
2026-09-02 02:03:49
3
chrsegu72 :
Looks like a T29 wheel.
2026-09-02 01:41:07
3
johnnyb_586 :
I’ve pissed off many safety guys off by doing this lol
2026-09-02 17:08:51
2
purescouse97 :
Leaving the backing nut on helps 🤦♂️🤦♂️🤦♂️
2026-09-08 16:36:54
1
Bora :
I would rather have a grinder with no guard for fiber and flapper disks. And a different grinder with the guard on to use cutting disks
2026-09-01 19:18:39
12
79burb :
Good tip man!
2026-09-02 14:35:49
3
Ian Davies 🏴 :
have 2 cordless and corded both don't have guards
2026-09-03 00:46:50
0
Jake Little :
which why most new grinders now have two peace guards. half that fully covers half of cutting wheels then can be removed for operations like youve shown.
2026-09-01 20:45:07
8
aidoelliott_ :
If you keep
2026-09-03 10:29:38
0
KB Steel Guy :
Do not cut guard to 120 degrees from 180 and repaint black !!!! safety
2026-09-02 23:25:24
2
Giovanni Lagudi :
Piss the guard off
2026-09-09 10:30:34
1
richard :
Those are guards? I thought they were only for shipping so I removed all of mine. 😎
2026-09-02 03:22:43
2
user6143449007278 :
Across the street this morning there is a guy working on a chimney. He has 3 levels of scaffold set up and is working from the top layer without no hand/saftey rails set up. So should I call the paramedics now or wait till he falls…
2026-09-02 15:58:14
1
timothygodfree :
fuckingoutstanding
2026-09-01 21:03:15
2
MarkD72 :
i use a 6" cutoff on my 4.5" all the time.
2026-09-01 21:13:25
3
Daedalus :
First thing I do AND remove about 7mm of the M14 spindle. The thread is flush with nut when I have a flappy on. Slightly proud with a skinny disk, the 1.2mm jobbies
2026-09-02 09:05:15
3
To see more videos from user @sheetmetalsamurai, please go to the Tikwm
homepage.
