ohio.carpenter
Region: US
Monday 28 September 2026 10:00:32 GMT
57432
741
83
2
Music
Download
Comments
johndufresnejr :
Have you heard of a speed square?
2026-09-28 16:56:59
38
Fakepersonmagnet :
running the saw the wrong direction, keep the wide part of the foot over the kept part of the board.
2026-10-08 07:43:01
1
jayrip :
well when you only hook one end and slide the other you get an arc
2026-09-28 18:37:08
11
HumungusChungus :
Looks good but would still take the 30 seconds to put a square and mark each board.
2026-09-28 10:53:06
13
posty :
don't do this
2026-09-29 00:41:54
15
gates420 :
if your cutting studs there all the same length board so just measure the small side
2026-09-29 01:46:06
14
Jdiggs :
You know you can just line up all the boards in one pile measure once cut the boards, the exact same length all the way through a lot faster and more efficient. You’re welcome.
2026-09-29 22:49:11
1
Kyle :
Please do not do this as an apprentice if the older guys see you do that and your cut isn’t perfect you won’t hear the end of it just pull your square out comparing to the time it will take you to perfect this you could’ve pulled your square out of your bags countless times they sell them for a reason because a human isn’t perfect
2026-09-30 05:16:41
3
Payday :
Doubt that’s square
2026-09-30 01:49:53
3
coarse :
Cut two at a time . The blade goes through the top and marks the second one .
2026-09-28 13:18:43
12
Ribble Dean :
I’d use a speed square on the first one, stack 5/7 studs, make them even, and your saw marks the one below, it’s called gang cutting
2026-09-28 18:12:53
6
805rick :
So no square? lol I bet he didn't even check the crown on the 2x4s 😂
2026-10-04 06:05:10
1
Kharn the bloody :
I just use my track saw, I can lay the track clamped down onto 2x4s that are double stacked on the saw horses, I can cut 14 in one pass. some people might laugh but I like knowing its a good cut
2026-09-29 02:19:59
2
Arques School :
you’re scribing a radius
2026-09-30 09:17:25
3
Vampire Alberta :
Studs are already specifically cut. Measure from the short side and use a square. No round cuts and just as fast.
2026-10-01 08:53:40
1
Jay Man :
Why are you putting a radius on your studs 😂😂
2026-09-29 00:12:51
4
Jay Jason Thompson :
I don't believe they were square
2026-09-29 15:29:08
4
Darren Butterfield :
nope
2026-09-30 00:43:05
1
DracoRiot :
jig.
2026-09-29 23:39:48
1
Zack Blake490 :
a double bottom plate you say? for what reason?
2026-09-28 21:02:05
1
devon..mccroy :
Line them up and use a straight edge from the first to last
2026-10-04 04:15:25
1
💀 :
Make a jig bro
2026-09-30 23:09:50
1
user2154627770762 :
no 👎
2026-09-28 23:09:31
1
wuzznexx :
On a clean stack just use a 4' level to offset the top rack of lumber and straighten the edge, measure on each outside board and use the level to scribe the line, cut, done.
2026-09-29 21:23:44
1
chooch :
you should have to mark all the way across, just one side, line up your circular saw so the plate is even as you cut across and itll be perfect
2026-09-29 00:00:48
4
To see more videos from user @ohio.carpenter, please go to the Tikwm
homepage.
