Odinary Z
Region: US
Wednesday 30 September 2026 16:46:03 GMT
70490
970
23
11
Music
Download
Comments
joshuashewmake4 :
You need to install them with a washer bolted to the pin so it sits right
2026-10-13 02:35:28
0
the dude :
I can appreciate a man and company that man’s up to a mistake and cover it. This is a lost principle of this country. Most companies look for any excuse to not cover their product
2026-09-30 22:51:48
8
fester 1966 :
looks to me like the bore in the gear is too deep with no shims the bearing clearance is controlled by shoulder of the pin to cone face on one side and the carrier housing to cone face on the other side THEN the depth of the bore to shoulder on gear (if the gear has an internal step in it )control the cup location.i agree with what the guy said about pressing the pin in the other direction I sometimes do that putting gear boxes with tapered roller bearings in.
2026-09-30 21:53:23
3
Peedmen :
you said you have done a bunch of these. how have you been doing all of these without measuring that depth to make sure it's correct. so you have been doing them all wrong.
2026-10-01 09:57:05
7
Sal :
you need a depth mic
2026-10-01 23:09:42
4
Brody Gilchuk :
Water is not going to get in from the Axle shaft seal. That Axle shaft seal has oil on both sides.
2026-10-02 02:47:01
5
Howie :
Did you find any rust???😳
2026-10-02 19:17:39
2
Jim :
Try a new set of bearings on the planetary shafts.
2026-09-30 18:01:08
3
LukeTheDuke :
+/-.02 might be ok with a caliper but +/-.002 a depth mic would be way more accurate
2026-10-02 14:17:56
3
poot hound :
the important thing is that you are correcting your mistake.
2026-10-02 03:38:50
2
chris Gerondale :
This is the best case I’ve ever made. I am crying because of how happy I am a company like yourself the customer failure you guys have some water intrusion.
2026-09-30 18:15:21
2
Tricky Ricky :
i bet it started making noise because warranty about out. i fixed a torque converter overheating by adjusting the decellerator peddle because it had converter in stall 1400 rpm while they were hooking the loggs.
2026-09-30 20:45:46
3
user839518 :
Lack of oil guys
2026-10-01 16:17:31
3
papashotrod :
Measure the depth of the hole and compare to the length of the pin. You may just be able to press it in until it stops.
2026-10-01 02:09:43
2
Larry :
lol
2026-10-01 00:50:38
2
cnctoolcat :
.005” is the thickness of a sheet of paper!
2026-10-01 01:15:49
1
cnctoolcat :
Check the spin of the bearing as you go! You will feel it stiffen up….
2026-10-01 01:19:26
3
tcob929 :
you should use a depth mic, not calipers
2026-10-02 18:04:15
3
johndeere9610 :
Freeze the shafts in liquid nitrogen and drop them in and it is perfect every time.
2026-10-04 18:45:27
3
chevy :
wish more shops would show your integrity
2026-09-30 23:48:30
3
Eric Williams :
❤️❤️❤️
2026-10-02 09:56:56
2
James Fitcher :
[Heartwarming][Heartwarming][Heartwarming]
2026-10-01 17:33:48
2
Chuck Wheeler :
😳😳😳
2026-10-13 20:51:38
0
To see more videos from user @odinaryz.us, please go to the Tikwm
homepage.
