1oz of hot water for the hot shot The temperature probe is in the lid of the rapid cool so I used to leave mine upside down while it was cooling so that I trusted when it was green
2026-11-19 15:32:19
0
Kayleigh Walsh :
It depends on how many ml/scoops of formula they’re on, I always did 10ml per scoop left in the bottle for the hot shot! I would then leave the lid off until it was drinking temp or if he was getting upset run the bottle with lid on under the cold tap! Don’t submerge MAM bottles in cold water though as they draw water in through the bottom, and if you end up putting formula in the rapid cool it needs washing & sterilising not just washing as formula is a breeding ground for bacteria 🥰
2026-11-02 19:52:22
1
xpollybarnard :
Hey, I was having the same issue for like a month of trying to use the rapid cool until I sussed out that I just wasn’t leaving it long enough to cool down (even though the light was showing green) so I recommend making sure there is no more than 30ml of boiling water in the bottom of your bottle and just leaving the rapid cool a little bit longer. For a 4oz bottle I pour 120ml into my mam, pour 90ml of it into nuby, turn it upside down and then press the top to see the yellow light and then I normally just leave it upside down, do my scoops and leave it for a further 30 secs and by then the water is normally cool enough to go in! Before I figured it out though I was just doing 30ml boiling hot water and 90ml cooled down boiled water it’s just as easy especially for night feeds rather than fussing with the nuby xxxx
2026-11-03 01:41:50
1
Bethany Watson :
I found the same, so would leave the kettle for 15 mins after boiling it then used it. Or if we was heading out putting it in a flask 15 minutes after boiling the kettle. Found the hot shot method made the bottles fat too hot if using it straight after it had been boiled xx
2026-11-02 19:47:25
1
Nat 🤍 :
I leave 10ml per oz, so if I did 6 oz bottle I’d leave 60ml in the bottle to mix in the formula & pour the rest of the water in the rapid cool, I have the Tommee tippee one but I leave it probably 3-4mins and it’s usually ready to go!! Xx
2026-11-03 07:15:51
3
SamP1390 :
From what I’ve seen the problem comes from the fact the nuby reduces the temp down to drinking temp (around 37°) but when you add that to the hot shot it’s still too hot. When you’re using a hot shot you need to be adding cooled water to bring the temperature down enough to be able to drink. Adding warm to hot is still too hot.
2026-11-02 21:35:41
1
ShaunaS :
Have a flask of cooled boiled water on the side filled up all day. 10ml boiling water per scoop of formula. Shake. The rapid cool has to reset after using (3 hours). Xx
2026-11-02 19:19:52
2
ellafx :
While your baby is on smaller ounces sadly you have to let your bottle to cool down!! I have been having this problem with my 4 week old. We have to put the bottle under cold tap to cool down or we have to wait 10 mins to cool down xx
2026-11-03 08:53:51
1
fxx11 :
I have two rapid cools and do the hot shot method if I have time to wait 5 mins ..change her nappy whilst it cools. Like someone else said the longer the water is in the rapid cool the colder it gets. Do a practice bottle with a food grade thermometer. The formula brings the temp of the water down also, which is why people aren’t happy with the Tommie tippie prep machines ( I have one of those too) xx
2026-11-02 19:40:57
1
Mell Powers | 📚 🦥 :
my 12 week old is on 6oz bottles. I have a flask filled with boiled water and I prep cooled boiled water the night before. 2oz boiled water, then add formula then add the pre measured (4oz) cooled water. has been perfect temp every time ☺️
2026-11-02 19:39:35
1
chloe|mum of 2 🩷💙 :
pour how many oz you give your baby In to the bottle then tip the some the hot water in the rapid cool but leave at 1oz on hot water in the bottle put you formula in give i little shake and shake you rapid cool intill it cool the add to the bottle give aother shake then done
2026-11-04 12:41:32
1
ashleigh.jordan00 :
my baby is 11 months so having a good 8oz bottle and i leave an oz of boiling water to shake with formula then cool the rest of the water with the rapid cool then mix all together. i only do this when we’re out and about but for a smaller bottle leaving an oz of boiling water might leave it far too hot! it’s tricky because you want the formula to be fully dissolved and NOT yellow!!
2026-11-02 19:15:45
1
rhi :
This!! I have to leave my bottle for about 20 mins before it’s cool enough to give to my baby 🥲 my baby’s feeds are too big to fit in the rapid cool mixed with the formula now but wish I could still just use it mixed 🥲
2026-11-03 09:32:32
1
harveyrice95 :
i pour 7 oz hot water into bottle. then pour 5 oz into rapid cool. scoop powder into the 2oz of hot then add rapid cool water once its cooled.
2026-11-03 13:28:46
1
ameliaaslett94 :
I do a hot shot with 4oz (120ml). leave about 1oz (30ml) in the bottle and the rest in the rapid cool. Always perfect. for 2oz or 3oz just leave about 15 - 20ml in the bottle
2026-11-06 18:17:17
1
Paige.Cooke :
Also I recommend putting the nuby in your fridge after each use🩷 it helps as typically you have to let it reset for 4 hours between each one
2026-11-02 19:53:38
1
Natalie Clarke :
i had the same problem with the rapid cool no matter what i did i had to wait a while for it to cool down. i started putting pre boiled cooled water in a baby bottle then doing the hot shot method then just adding cooled boiled water with the hot shot method and it was perfect everytime. sounds complicated but trust me its so easy xx
2026-11-03 21:52:34
3
Nicola :
Can I ask… if we are cooling down the water in the rapid cool. Can’t we just use a bit more boiling water for the formula and then topping up with cold water?
2026-11-03 08:33:53
0
Paige.Cooke :
How many oz does he take and I can message you girl! My boy is 18 months now so i did it for a year x
2026-11-02 19:52:40
1
Sophie :
I always put the bottle with the hot shot in a cup of cold water so it can cool down while the rest of the water is in the rapid cool! It’s ready to use in less than 5 minutes x
2026-11-03 08:43:19
2
Nicole Clitheroe :
Once the rapid cool is washed and sterilised it needs to sit at room temperature for at least 3 hours for the thermometer to reset. The rapid cool then needs tipped upside down for at least 10 seconds for it to kick in. It also needs at least 3oz for it to work as well. I find the light always goes green way too soon so I just flip it up and down until it’s cool enough when I test it
2026-11-05 12:21:02
1
Christine Brogan🤍 :
My son is on 6 ounces I do 2 ounces of boiling water and the rest in the rapid cool x
2026-11-03 18:18:57
1
Andrea ◕‿◕ :
I make mine for twins so I have double the amount of water in my rapid cool, I leave it an extra 5 mins giving it a little shake too, how many mls you leaving in :)?
2026-11-03 14:47:40
0
M123456s :
Also for the during the night one I make up boiling then refrigerate when it’s cooled then just heat it up although the bottle warmer we have is probs as long as making up a bottle sometimes I just use a cup of boiling water to tske the chill off. NHS guidance is that it can be stored in fridge for 24 hours xx
2026-11-03 22:30:27
1
Erin🫶🏼 :
I always need to shake my Nuby quite a lot and wait until the outside of it gets hot. The Nuby will also show green before it’s actually cooled enough. Who knows why 🤷🏻♀️also try not to use boiling water straight from the kettle let it cool a bit
2026-11-03 04:42:12
3
To see more videos from user @zoealice_w, please go to the Tikwm
homepage.